FILTERS


By Product Category

  • Respiratory

By Product Sub-Category

  • BIPAP

By Product Brand

  • Resmed

Resmed AirCurve™ 10 V Auto

Specifications

  • Height    116 mm
  • Weight    1248 gm
  • Breadth    150 mm
  • Length    255 mm
  • Sound pressure level    
  • Supplemental oxygen Maximum flow    15 L/min (CPAP, S); 4 L/min (VAuto)
  • Storage and transport humidity    5 to 95%relative humidity, non-condensing
  • Ramp Time    You can set your Ramp Time to Off or between 5 to 45 minutes.
  • Water capacity:    To maximum fill line 380 mL
  • Air outlet    22 mm
  • Typical power consumption    53W (57VA)
  • Sensors    Pressure sensor: Internally located at device outlet, analoguegauge pressure type, -5 to +45cmH2O (-5 to +45 hPa); Flow sensor:Internally located at device inlet, digital mass flow type, -70 to +180 L/min
  • Operating altitude    Sea level to 2,591m; air pressure range 1013hPa to 738 hPa
  • Maximum single fault steady state pressure    Device will shut down in the presence of a single fault if the steady state pressure exceeds:30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec
  • Modes    S, VAuto, CPAP
  • Sound power level    Pressure level measured according to EN ISO 17510-1:2009 (CPAP mode):SlimLine:26.6 dBA with uncertainty of 2 dBAStandard:26.6 dBA with uncertainty of 2 dBAPower level measured according to EN ISO 17510-1:2009 (CPAP mode):SlimLine:34.6 dBA with uncertainty of 2 dBAStandard:34.6 dBA with uncertainty of 2 dBADeclared dual-number noise emission values in accordance with ISO4871:1996.
  • Peak power consumption    104W (108VA)
  • Operating pressure range    S, VAuto: 2 to 25cm H2O (2 to 25 hPa); CPAP: 4 to 20cmH2O (4 to 20 hPa)
  • Power supply unit    90W power supply unit; AC input range:100–240V, 50–60Hz 1.0–1.5A, Class II115V, 400Hz 1.5A, Class II (nominal for aircraft use); DC output:24V 3.75A
  • Storage and transport temperature    -20°C to +60°C
  • Operating humidity    10 to 95% relative humidity, non-condensin
  • Housing construction    Flame retardant engineering thermoplastic
  • Operating temperature    +5°C to +35°C Note: The air flow for breathing produced by this therapy device can be higher than the temperature of the room. Under extreme ambient temperature conditions (40°C) the device remains safe.
  • Wireless Module    Technology used:4G, 2G. It is recommended that the device is a minimum distance of 2 cm from the body during operation. Not applicable to masks, tubes or accessories. Technology may not be available in all regions
  •  

Resmed AirCurve™ 10 V Auto

Specifications

  • Height    116 mm
  • Weight    1248 gm
  • Breadth    150 mm
  • Length    255 mm
  • Sound pressure level    
  • Supplemental oxygen Maximum flow    15 L/min (CPAP, S); 4 L/min (VAuto)
  • Storage and transport humidity    5 to 95%relative humidity, non-condensing
  • Ramp Time    You can set your Ramp Time to Off or between 5 to 45 minutes.
  • Water capacity:    To maximum fill line 380 mL
  • Air outlet    22 mm
  • Typical power consumption    53W (57VA)
  • Sensors    Pressure sensor: Internally located at device outlet, analoguegauge pressure type, -5 to +45cmH2O (-5 to +45 hPa); Flow sensor:Internally located at device inlet, digital mass flow type, -70 to +180 L/min
  • Operating altitude    Sea level to 2,591m; air pressure range 1013hPa to 738 hPa
  • Maximum single fault steady state pressure    Device will shut down in the presence of a single fault if the steady state pressure exceeds:30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec
  • Modes    S, VAuto, CPAP
  • Sound power level    Pressure level measured according to EN ISO 17510-1:2009 (CPAP mode):SlimLine:26.6 dBA with uncertainty of 2 dBAStandard:26.6 dBA with uncertainty of 2 dBAPower level measured according to EN ISO 17510-1:2009 (CPAP mode):SlimLine:34.6 dBA with uncertainty of 2 dBAStandard:34.6 dBA with uncertainty of 2 dBADeclared dual-number noise emission values in accordance with ISO4871:1996.
  • Peak power consumption    104W (108VA)
  • Operating pressure range    S, VAuto: 2 to 25cm H2O (2 to 25 hPa); CPAP: 4 to 20cmH2O (4 to 20 hPa)
  • Power supply unit    90W power supply unit; AC input range:100–240V, 50–60Hz 1.0–1.5A, Class II115V, 400Hz 1.5A, Class II (nominal for aircraft use); DC output:24V 3.75A
  • Storage and transport temperature    -20°C to +60°C
  • Operating humidity    10 to 95% relative humidity, non-condensin
  • Housing construction    Flame retardant engineering thermoplastic
  • Operating temperature    +5°C to +35°C Note: The air flow for breathing produced by this therapy device can be higher than the temperature of the room. Under extreme ambient temperature conditions (40°C) the device remains safe.
  • Wireless Module    Technology used:4G, 2G. It is recommended that the device is a minimum distance of 2 cm from the body during operation. Not applicable to masks, tubes or accessories. Technology may not be available in all regions
  •  

Resmed AirSense 10 Autoset Tripack 3G CPAP Device

Specifications

  • Height    116 mm
  • Weight    1248 gm
  • Breadth    255 mm
  • Length    150 mm
  • Pressure measurement tolerance    ±[0.5 cm H20 (0.5 hPa) + 4% of measured value]
  • Flow measurement tolerance    ±6 L/min or 10% of reading, whichever is greater, at 0 to 150 L/min positive flow
  • Peak power consumption    104W (108VA)
  • Operating pressure range    4 to 20 cm H2O
  • Supplemental oxygen Maximum flow    4 L/min
  • Power supply unit    90W power supply unit
  • Storage and transport humidity    5 to 95% relative humidity, non-condensing
  • Storage and transport temperature    -4°F to +140°F (-20°C to +60°C)
  • Operating humidity    10 to 95% relative humidity, non-condensing
  • Housing construction    Flame retardant engineering thermoplastic
  • Water capacity:    To maximum fill line 380 mL
  • Air outlet    22 mm (complies with ISO 5356-1:2004)
  • Typical power consumption    53W (57VA)
  • Sensors    Pressure sensor: Internally located at device outlet, analog gauge pressure type, -5 to +45 cm H2O (-5 to +45 hPa) Flow sensor: Internally located at device inlet, digital mass flow type, -70 to +180 L/min
  • Operating altitude    Sea level to 8,500' (2,591 m); air pressure range 1013 hPa to 738 hPa
  • Operating temperature    +41°F to +95°F (+5°C to +35°C)
  • Maximum single fault steady state pressure    Device will shut down in the presence of a single fault if the steady state pressure exceeds: 30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec
  • Modes    CPAP

Resmed AirSense 10 Autoset Tripack 3G CPAP Device

Specifications

  • Height    116 mm
  • Weight    1248 gm
  • Breadth    255 mm
  • Length    150 mm
  • Pressure measurement tolerance    ±[0.5 cm H20 (0.5 hPa) + 4% of measured value]
  • Flow measurement tolerance    ±6 L/min or 10% of reading, whichever is greater, at 0 to 150 L/min positive flow
  • Peak power consumption    104W (108VA)
  • Operating pressure range    4 to 20 cm H2O
  • Supplemental oxygen Maximum flow    4 L/min
  • Power supply unit    90W power supply unit
  • Storage and transport humidity    5 to 95% relative humidity, non-condensing
  • Storage and transport temperature    -4°F to +140°F (-20°C to +60°C)
  • Operating humidity    10 to 95% relative humidity, non-condensing
  • Housing construction    Flame retardant engineering thermoplastic
  • Water capacity:    To maximum fill line 380 mL
  • Air outlet    22 mm (complies with ISO 5356-1:2004)
  • Typical power consumption    53W (57VA)
  • Sensors    Pressure sensor: Internally located at device outlet, analog gauge pressure type, -5 to +45 cm H2O (-5 to +45 hPa) Flow sensor: Internally located at device inlet, digital mass flow type, -70 to +180 L/min
  • Operating altitude    Sea level to 8,500' (2,591 m); air pressure range 1013 hPa to 738 hPa
  • Operating temperature    +41°F to +95°F (+5°C to +35°C)
  • Maximum single fault steady state pressure    Device will shut down in the presence of a single fault if the steady state pressure exceeds: 30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec
  • Modes    CPAP

aaa